Guide 02 · About 6 minutes
USB turntable, phono preamp or mixer?
To record vinyl on a phone, the audio has to reach it as a digital stream over USB. There are three common ways to get it there. Which one is yours depends on what’s already on your shelf.
The short answer
- A turntable with a USB socket: plug it straight into the phone.
- A record player without USB: put a USB phono preamp in between.
- A DJ setup: use a mixer with USB audio and a phono input, or a phono preamp into a USB audio interface.
Why USB, and not a microphone or a cable to the headphone jack
A phone’s microphone records the room: the speakers, the fridge, the needle’s own chatter. And a phone’s headphone socket, where it still has one, is an output, or at best a mono headset microphone input. Neither gives you a clean stereo copy of the record.
A USB audio device does the conversion to digital itself and sends the phone the finished stream, the same one a computer would get. That is why StylusLog records USB audio only, and never uses the microphone.
What a phono preamp does
A cartridge’s output is tiny, a few thousandths of a volt, and it isn’t flat: records are cut with the bass turned down and the treble turned up (the RIAA curve), so the groove stays narrow and quiet. A phono preamp, or phono stage, adds the gain and undoes the curve.
Every setup below has one somewhere: built into the USB turntable, in the USB preamp box, or in the mixer’s phono channel. Skip it and the recording comes out very quiet, thin and bright, with no bass. StylusLog’s report flags exactly that as “No phono preamp?”.
1. A USB turntable
Many turntables sold for digitizing have a USB socket on the back, with a phono preamp and an analog-to-digital converter built in. Connect it to the phone with a USB cable and it appears as a USB audio device.
- Good: one cable, nothing else to buy.
- Check: a PHONO/LINE switch on the back sets what the RCA outputs carry for your amplifier. If the USB recording comes out very quiet with no bass, try the other setting.
- Expect: 16-bit audio at 44.1 or 48 kHz from most of them, which covers what a record holds.
2. A record player and a USB phono preamp
Already have a turntable you like, without USB? A USB phono preamp sits between it and the phone. The turntable’s RCA leads go into the preamp’s phono input, and its USB output goes to the phone. Many also have line outputs for your amplifier, so the hi-fi stays connected.
- Good: keeps your turntable and cartridge.
- Check: the preamp suits your cartridge. Most phono preamps are for moving-magnet (MM) cartridges; a moving-coil (MC) cartridge needs more gain.
- Connect the ground wire from the turntable to the preamp’s ground terminal. Without it you get hum at 50 or 60 Hz, which the report will point out.
3. A DJ mixer’s phono channel
Many club and DJ mixers have a USB port that works as an audio interface, carrying each channel’s input to the computer, or to a phone. Plug the turntable into a channel’s phono input, set that channel’s rear switch to PHONO, and connect the mixer’s USB to the phone.
- Good: the mixer’s phono stage, and its meters, are already there.
- Check: StylusLog follows the channel that’s playing; tap Change under the meters to pick another.
A phono preamp into a USB audio interface works the same way: the preamp’s line output goes into the interface’s line inputs, and the interface’s USB to the phone.
Will my device work with a phone?
StylusLog records from class-compliant USB audio (USB Audio Class 1 and 2), the standard that lets audio devices work without installing a driver. Most USB turntables, USB phono preamps, DJ mixers and audio interfaces follow it.
- Good sign: it works on a Mac or a PC without installing anything.
- Bad sign: it needs a driver from the maker’s website on Windows and on a Mac.
- Power: a device with its own power supply puts no load on the phone. One powered from the USB cable runs from the phone’s battery.
- The port: a phone with USB-C takes a USB-C cable or adapter; an older micro-USB phone needs a USB OTG adapter.
Try before you pay. Plug your gear into StylusLog first: it shows whether the device connects, and the meters show the record playing, before you buy anything. Tried it? Send the diagnostic log from the app’s menu, whether it worked or not.
When something’s off
| What you hear or see | Likely cause | Fix |
|---|---|---|
| The meters don’t move | Wrong input, or the preamp is off | On a mixer, pick the channel and set its switch to PHONO; check power and cables |
| Very quiet, thin, no bass | No phono preamp in the chain | Switch the built-in preamp on, or use the PHONO input |
| A low hum | Ground wire not connected | Connect it to the preamp’s ground terminal; keep cables away from power leads |
| Distorted loud parts | Level too high | Lower the gain on the preamp until peaks sit around −6 dBFS |
| One side quieter | Cartridge or its leads | Check the four small cartridge leads are on firmly |
Ready to record? How to digitize vinyl on an Android phone walks through a whole album, from the level to the FLAC files.
See if your setup connects
StylusLog is free to try on your first three albums, on Android 8.0 and later and on iPhone with iOS 15 and later.
